Home » Service » Downloads »



multiMAUS  Downloads


Use instructions

 MultiMAUS
 
 multiMAUS Pro

 

multiMAUS Update

Update via Z21:
 
     

    multiMAUS Firmware and language update

    For the majority of users multiMAUS there is no reason their multiMAUS update with this firmware update. The version V1.00, delivered since production began running stable.

    However, those who want to have a different language pack, or have problems with the following items, which should update to the new version:
    • You want to address decoder functions F13 to F20 (if your decoder supports this, and these are assigned).
    • You have to program some problems decoder types of other manufacturers.
    • You have more than 10 feedback modules 10787 in use.
    • You get when programming in POM mode with the LENZ center the error message "ERR1" at the multiMAUS.
    • Although no feedback contacts are pressed into blocks flashing sporadically Rocomotion pink (is) on.
    If any of these apply to you, we recommend that you update to V1.02.

    Notes:
    Your multiMAUS settings, and the entries in the locomotive database are retained even after the update.
    At the multiMAUS You can menu: "Settings" - menu "Info" - submenu "software" check the current version (eg V 1-00).
    multiMAUS users who can not have available this multiZENTRALEpro send through retailers to customer service.


    Update instructions for the multiMAUS
    It is the multiZENTRALEpro 10,830, and requires the desired MultiMausUpdate.EXE.

    Connect the multiZENTRALEpro via the USB cable to the PC. Close the multiMAUS to be updated on the "Feedback BUS" jack on the back of the multiZENTRALEpro.
     
    Important Information!
    Other devices that connect to the "RocoNet" jacks remain, they do not work during the upgrade process.
    ROCOMOTION software or TrainProgrammer not start or only offline mode.
    Do not interrupt the update process not by unplugging the multiMAUS the multiZENTRALEpro or other connected equipment. Should this happen, the multiMAUS shows "Err 99". You need to update and then again start to finish, so that the multiMAUS is functional again.
    Double click to open the "MM_Update_xxx.exe" file.


    The following window appears:




    Press "Start" and follow the instructions on the screen

    The update begins.



     
    After successfull completion the following window appears:


    If another multiMAUS be updated, the process can be restarted after connecting another multiMAUS.
     
With the Firmware Version V1.09 you can use the multiZENTRALEpro and the multiMAUSpro as a LocoNet Slave on the Z21.
    Connect to the EXT-socket of the multiZENTRALEpro via the L-BUS socket of the Z21. The Z21 then supplies the multiZENTRALEpro via the LocoNet with power (12VDC). Therefore no power supply should be connected to the MultiZENTRALEpro.





                If you wish to use the multiZENTRALEpro with other LocoNet Masters then please consider the following:
                  In this case the multiZENTRALEpro has its own power supply and must be connected to the LocoNet Master via a white "LocoNet Slave Cabel" (Spare part number 136100).
                    This cable can be purchased from you dealer or online at roco.cc - Service – Ersatzteile (Spare parts).
                      The white LocoNet Slave Cabel isolates inadmissible supply voltages in the
                        LocoNet Bus (Pin1 and Pin6) of the multiZENTRALEpro.
                          This is the only way to ensure a problem-free operation if you wish to use other central control systems.
                            The use of an inappropriate cable can even destroy the central control systems.




                                      multiZENTRALEpro/ multiMAUSpro Software


                                      Starting with multiZENTRALEpro firmware V1.09 you can run your multiZENTRALEpro plus multiMAUSpro as LocoNet slave on the Z21.


                                      Solved multiZENTRALEpro Failures:


                                      • The computation of long loco addresses has been adapted to the Z21 LAN protocol 1.07, in oder to avoid incorrect computed addresses in the range 100 to 128 when using the multiZENTRALEpro as LocoNet slave on the Z21.


                                      Solved multiMAUSpro Failures:


                                      • The computation of long loco addresses has been adapted to the Z21 LAN protocol 1.07, in oder to avoid incorrect computed addresses in the range 100 to 128 when using the multiZENTRALEpro as LocoNet slave on the Z21.
                                      • Losing the speed steps setting, i.e., falling back to the default value “14 Speed Steps”, after turning on the device is not possible anymore.
                                      • Resuming a child-proof lock code or assigning the default value “0000” despite leaving the input editor with the STOP-key is not possible anymore.
                                      • Changes in brightness and contrast are now visualized during the input.


                                      Previous Versions:


                                      Rocomotion
                                        Rocomotion Software - Upgrade v.5.9 A1: "Rocomotion_59_A1.zip"
                                         
                                         
                                         
                                         
                                        Product
                                        News
                                        Dealer
                                        Specials
                                        Service
                                        About us